User guide

This user guide describes how to set up the ADAR3000/3001-EVALZ evaluation board for the ADAR3000 and ADAR3001, and how it connects to an FPGA carrier. The ADAR3000 and ADAR3001 data sheets provide additional information and should be consulted when using the evaluation board.

Evaluation board hardware

The ADAR3000/3001-EVALZ carries the beamformer, with its RF inputs RFIN1 to RFIN4 and RF outputs RFOUT1 to RFOUT4 on 2.92 mm connectors, as single-ended 50 Ω coplanar waveguides. It is controlled through the 120-pin SDP connector P5. On the bench it is usually driven by an SDP-S controller board and the ACE software; in this reference design an SDP-I-FMC interposer adapts P5 to the FMC connector of the FPGA carrier instead.

Power supply

The evaluation board is supplied from two bench supplies, applied to the test loops on the board:

Table 1 Power supplies

Rail

Test loops

Supply capability

Expected draw

1.2 V analog

Red 1P2V to AGND

250 mA

128 mA ± 12 mA (ADAR3000), 110 mA ± 10 mA (ADAR3001)

1.8 V digital

Red 1P8V to DGND

20 mA

7 mA ± 3 mA

The expected draw applies after power up and a soft reset, when the amplifiers are enabled with their default bias setting of 3. With the amplifiers disabled, the 1.2 V draw drops to about 1 mA.

The data sheet gives absolute maximum ratings of 1.32 V on V1P2 and 1.98 V on V1P8, so set the over-voltage protection of the supplies below those values.

Hardware configuration

Set the jumpers as follows for control from an FPGA carrier:

Table 2 Jumper settings

Header

Setting

Function

P8

Pin 1 to pin 2

Connects the chip’s internal 1.0 V LDO output. Required.

P9

Pin 1 to pin 2

Connects the chip’s internal 1.0 V LDO output. Required.

P4

Pin 1 to pin 2

Ties RESET_N (RSTB) to 1.8 V, as shipped. The no-OS project does not drive RSTB and resets the device with the soft reset sequence. Pin 2 to pin 3 holds the device in reset.

P2

Open

Fitted, it forces the board SPI mux to bit-banged GPIO SPI.

P12

Open

Fitted, it disables the SPI level translator U1.

P13

Open

Fitted, it disables the control pin level translator U3.

P6

No jumpers

ADDR[3:0] chip address pins, pulled down to address 0. Fit jumpers to give the device another address, matching the dev_addr the software uses.

Other headers expose signals for monitoring:

Table 3 Monitoring headers

Header

Signals

P1

SPI and beam command signals at 1.8 V, after the level translators, plus the 1.2 V and 1.8 V supplies

P10

SPI signals at VIO, before the level translators, plus the supplies

P14

SDP connector signals at VIO: SPI and GPIO0 to GPIO7

P3

ADC inputs ANLG0 (pin 1) and ANLG1 (pin 3)

P7

DAC output (pin 1)

P11

Chip GPIO0 to GPIO3

Control interface

All control signals reach the device through the SDP connector P5. The logic level on the SDP side is VIO, which the controller supplies on P5: 3.3 V from an SDP-S, and the FMC VADJ rail through the SDP-I-FMC interposer. Two level translators shift VIO to the device’s 1.8 V:

  • U1 carries the SPI: chip select, clock, MOSI and MISO.

  • U3 carries the control pins: RESET_N (RSTB), UPDATE, RESET and MUTE.

Ahead of U1, the 2:1 mux U5 selects the SPI source. With its select input, SDP GPIO3, low it passes the SDP hardware SPI; with it high it passes bit-banged SPI on SDP GPIO0 to GPIO2.

On the ZCU102, the SPI comes from the ZynqMP PS SPI0 controller routed through EMIO, and the control pins from EMIO GPIOs:

Table 4 ZCU102 control signals

Signal

ZynqMP source

Function

SPI0

PS SPI0 via EMIO

Register access, mode 0, MSB first, up to 1 MHz

spi_sel_a

spi0_csn[0]

Chip select

GPIO 3

EMIO 35

SPI mux select, driven low

GPIO 4

EMIO 36

UPDATE, beamstate update strobe

GPIO 5

EMIO 37

RESET, beam reset qualifier

GPIO 6

EMIO 38

MUTE, beam mute qualifier

GPIO 7

EMIO 39

RESET_N (RSTB), not driven, see P4 above

The no-OS driver drives the mux select low during initialization. The complete HDL interface is documented in the ADAR3000 HDL project.

FMC VADJ

Through the interposer, VIO is the carrier’s FMC VADJ rail, which must be at 1.8 V. VADJ also supplies the FPGA I/O banks behind the FMC connector; at 0 V no pin on that connector can drive, and the SDP side of the level translators is unpowered.

On the ZCU102, VADJ is not fixed. At power up the board’s system controller reads the IPMI FRU EEPROM of the card in the FMC slot, per the VITA 57.1 standard, and sets VADJ from the DC Load record it finds. If no valid record is present it leaves VADJ at 0 V. With this setup the card in the FMC slot is the SDP-I-FMC interposer, and it ships with a blank EEPROM.

The symptom is easy to misread: the FPGA configures, the application runs, SPI initialization succeeds, and every register read returns 0xFF because MISO floats. The 1.8 V supply of the evaluation board may also draw far more than expected, around 47 mA instead of 7 mA, as the control lines drive into the unpowered FPGA I/O bank. If the no-OS example reports a scratchpad mismatch, check VADJ before suspecting the software or the wiring.

To set VADJ to 1.8 V, either:

  • program the interposer’s FRU EEPROM with a record requesting 1.8 V, which persists across power cycles. See FMC EEPROM Programming.

  • or override VADJ with the ZCU102 system controller user interface, as described in the ZCU102 Evaluation Board User Guide (UG1182). The override does not persist and has to be repeated after every power cycle.

Schematic, PCB Layout, Bill of Materials

The board is the ADAR3000/3001-EVALZ, schematic 02-059137 revision C. Contact Analog Devices for its design files.